Programmierung / Konfigurationen

Hallo Zusammen,

Ich ab jetzt schon einige Einträge gefunden welche beschreiben wie man z.B. die "Tür zu ab 30 km/h " programmiert.

Kennt jemand eine Übersicht über alle möglichen Konfigurationen ?

Danke und Gruss

Frank

 

Hmm,

ich suche eine Sammlung aller möglichen Konfigurationen welche ich ohne besonderes Zubehör durchführen kann.

z.B. per Zündschüßel an aus an aus........

 

Hier mal alles was ich so gefunden hab.


BeltAlert can be enabled or disabled by your authorized
dealer or by following these steps:
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. Chrysler Group LLC does not recommend
deactivating BeltAlert.
1. Turn the ignition switch to the OFF position, and
buckle the driver’s seat belt.
2. Turn the ignition key to the ACC/ON position (do not
start the engine), and wait for the Seat Belt Reminder
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver’s seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.
4. Turn the ignition key to the OFF position. A single
chime will sound to signify that you have successfully
completed the programming.



Oder



NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. Chrysler Group LLC does not recommend
deactivating BeltAlert.
1. Turn the ignition switch to the OFF position, and
buckle the driver’s seat belt.
2. Turn the ignition key to the ACC/ON position (do not
start the engine), and wait for the Seat Belt Reminder
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver’s seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.
4. Turn the ignition key to the OFF position. A single
chime will sound to signify that you have successfully
completed the programming.
BeltAlert can be reactivated by repeating this procedure.
NOTE: Although BeltAlert has been deactivated, the
Seat Belt Reminder Light will continue to illuminate
while the driver’s seat belt remains unfastened.



K Wrangler Tweaks

Auto-lock at 15 mph with NO auto unlock all when either front door is opened
Insert the key. Cycle the key from insertion position to "on" position 5 times. Upon completing the 5th cycle make sure the key ends in the "on" position, press the Unlock switch up once.

Auto-lock at 15 mph and auto unlock all when either front door is opened
Insert the key. Cycle the key from insertion position to "on" position 5 times. Upon completing the 5th cycle make sure the key ends in the "on" position, press the Unlock switch up twice.

HONK when locking with keyfob
Press and hold the Lock button on the fob for at least 5 seconds. While still holding the Lock button, press the Panic button and release both. Test operation.

One-touch unlock all the doors with keyfob
Press and hold the Lock button on the fob for at least 5 seconds but no more than 10. While still holding the Lock button press and hold the Unlock button. Release both and test.

Lights flash when locking with keyfob
Press the Unlock button on the fob for 4 to 10 seconds. While still holding the Unlock button press and hold the Lock button. Release both and test.

Seat Belt Chime
Turn the ignition switch to the OFF position, and buckle the driver or front passenger seat belt. Turn the ignition key to the ACCESSORY/RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver or front passenger seat belt at least three times within 10 seconds, ending with the seat belt buckled. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming.