zündkerzenwechsel beim kj

tomb-raider · 22.08.2012

Hallo .
Ich weiß nicht wie man die Zündkerzen bei meinem kj v6 wechselt.
Kann mir da irgentjemand helfen?
Gruß tomb-raider

samse2101 · 22.08.2012

Puh, ich dachte bald echt schon, der KJ ist nur ein Auto für Anzugträger....

Aber anscheinend gibts doch noch ein paar die gern selbst Hand anlegen...

Leider nur in Englisch, aber ein bisschen Englisch-Übung scahdet nie:

Ausbau der Zündspulen (ignition coils)

3.7L
An individual ignition coil is used for each spark plug. The coil fits into machined holes in the cylinder head. A mounting stud/nut secures each coil
to the top of the intake manifold. The bottom of the coil is equipped with a rubber boot to seal the spark plug to the coil. Inside each rubber boot is a spring. The spring is used for a mechanical contact between the coil and the top of the spark plug. These rubber boots and springs are a permanent part of the coil and are not serviced separately. An o-ring is used to seal the coil at the opening into the cylinder
head.
(1) Depending on which coil is being removed, the
throttle body air intake tube or intake box may need
to be removed to gain access to coil.
(2) Disconnect electrical connector from coil by
pushing downward on release lock on top of connector
and pull connector from coil.
(3) Clean area at base of coil with compressed air
before removal.
(4) Remove coil mounting nut from mounting stud
(Fig. 17).
(5) Carefully pull up coil from cylinder head opening
with a slight twisting action.
(6) Remove coil from vehicle.

Ausbau der Zündkerze (spark plug):

3.7L
Each individual spark plug is located under each
ignition coil. Each individual ignition coil must be
removed to gain access to each spark plug. Refer to
Ignition Coil Removal/Installation.
(1) Prior to removing ignition coil, spray compressed
air around coil base at cylinder head.
(2) Prior to removing spark plug, spray compressed
air into cylinder head opening. This will help
prevent foreign material from entering combustion
chamber.
(3) Remove spark plug from cylinder head using a
quality socket with a rubber or foam insert. Also
check condition of ignition coil o-ring and replace as
necessary.
(4) Inspect spark plug condition. Refer to Spark
Plug Conditions.

CLEANING
CLEANING SPARK PLUGS
The plugs may be cleaned using commercially
available spark plug cleaning equipment. After cleaning,
file the center electrode flat with a small point
file or jewelers file before adjusting gap.
CAUTION: Never use a motorized wire wheel brush
to clean the spark plugs. Metallic deposits will
remain on the spark plug insulator and will cause
plug misfire.

Einbau der Zündkerze:

3.7L
Special care should be taken when installing spark
plugs into the cylinder head spark plug wells. Be
sure the plugs do not drop into the plug wells as electrodes
can be damaged.
Always tighten spark plugs to the specified torque.
Over tightening can cause distortion resulting in a
change in the spark plug gap or a cracked porcelain
insulator.

(1) Start the spark plug into the cylinder head by
hand to avoid cross threading.
(2) Tighten spark plugs. Refer to torque specifications.
(3) Before installing coil(s), check condition of coil
o-ring and replace as necessary. To aid in coil installation,
apply silicone to coil o-ring.
(4) Install ignition coil(s). Refer to Ignition Coil
Removal/Installation.

Einbau der Zündspule:

3.7L
(1) Using compressed air, blow out any dirt or contaminants
from around top of spark plug.
(2) Check condition of coil o-ring and replace as
necessary. To aid in coil installation, apply silicone to
coil o-ring.
(3) Position ignition coil into cylinder head opening
and push onto spark plug. Do this while guiding coil
base over mounting stud.
(4) Install coil mounting stud nut. Refer to torque
specifications.
(5) Connect electrical connector to coil by snapping
into position.
(6) If necessary, install throttle body air tube or
box.
Klicke in dieses Feld, um es in vollständiger Größe anzuzeigen.

mfg
samse

tomb-raider · 23.08.2012

danke für die schnelle Antwort.
dann werde ich mal mein altes Wörterbuch raus holen
und sehen,was ich davon alles verstehe.
Möchte so viel wie möglich selber machen.
nur beim einstellen meiner Gasanlage muß der
Fachmann ran.
Gruß tomb-raider

samse2101 · 23.08.2012

Zitat von tomb-raider: ↑

...Möchte so viel wie möglich selber machen....
Klicke in dieses Feld, um es in vollständiger Größe anzuzeigen.

Super!

tomb-raider · 15.09.2012

Jeeeepie!!!
die Zündzerzen sind gewechselt.
Hat etwas über zwei Stunden gedauert.
Danke nochmal für die Hilfe.

liebe Grüße Tomb-raideer

zündkerzenwechsel beim kj

tomb-raider man sieht sich immer zweimal!

samse2101 Guest

tomb-raider man sieht sich immer zweimal!

samse2101 Guest

tomb-raider man sieht sich immer zweimal!

zündkerzenwechsel beim kj

Nützliche Suchen

zündkerzenwechsel beim kj

tomb-raider man sieht sich immer zweimal!

samse2101 Guest

tomb-raider man sieht sich immer zweimal!

samse2101 Guest

tomb-raider man sieht sich immer zweimal!

zündkerzenwechsel beim kj